Pico Technology TA Series TA044 Oscilloscope Probe, Differential Type, 70 MHz, BNC Connector

모든 Oscilloscope Probes 열람하기

Subtotal (1 unit)*

₩2,009,143.50

Add to Basket
수량 선택 또는 입력
재고있음
  • 추가로 2026년 5월 04일 부터 31 개 단위 배송
  • 추가로 2026년 5월 27일 부터 10 개 단위 배송
더 자세한 내용이 필요하신가요? 필요한 수량을 입력하고 '배송일 확인'을 클릭하면 더 많은 재고 및 배송 세부정보를 확인하실 수 있습니다.
수량
한팩당
1 +₩2,009,143.50

* 참고 가격: 실제 구매가격과 다를 수 있습니다

RS 제품 번호:
898-6750
제조사 부품 번호:
TA044
제조업체:
Pico Technology
제품 정보를 선택해 유사 제품을 찾기
모두 선택

브랜드

Pico Technology

Product Type

Oscilloscope Probe

Probe Type

Differential

Bandwidth

70MHz

Maximum Common Mode Input Voltage

5kV

Connector Type

BNC

Model Number

TA044

Number of Probes

2

Safety Category Level

CAT I

Safety Category Voltage

2500V

Series

TA

Standards/Approvals

IEC 1010-2-031

Rise Time

5ns

Pico Technology Oscilloscope Probe


The Pico Technology TA044 oscilloscope probe is an active differential probe, suitable for high common-mode voltage measurement applications up to ±7000V. It can be used with a signal speed of up to 70Hz. This differential probe extends the functionality of standard single-ended input oscilloscopes to allow a safe and accurate method of making high voltage differential measurements.

By selecting attenuation ratio 1:100, this oscilloscope probe can measure signals below 70V to get higher resolution and less noise. Otherwise, set the attenuation to 1:1000.

Features and Benefits


Bandwidth is DC to 70MHz (–3dB)

Attenuation ratio is 100:1/1000:1

Accuracy is ±2%

Input impedance is 10Mohm ll10pF each side to ground

Differential range is (100:1) ±700V (DC + peak AC) or 700VRMS

Maximum differential is (1000:1) ±7000V (DC + peak AC) or 5000VRMS

Common mode range is ±7000V (DC + peak AC) or 2500VRMS (100:1 & 1000:1)

Absolute maximum voltage is ±7000V (DC + peak AC) or 2500VRMS (100:1 & 1000:1)

Absolute maximum voltage is (differential mode) ±7000V (DC + peak AC) or

5000VRMS (100:1 & 1000:1)

Swing is ±7V into 50kohm load

Offset (typical) is <±5mV

Noise (typical) is 0.9mVRMS

Source impedance is (typical) 50ohm

CMRR (typical) is 80dB at 6Hz and 50dB at 1MHz

Ambient operating temperature ranges between -10°C and 40°C

Power requirement 4xAA cells or 6VDC/200mA mains adaptor or regulated 9VDC/120mA mains adaptor

Input lead length 600 mm

BNC lead length 900 mm

Dimensions (LxWxH): 202 x 83 x 38 mm

Applications


Safe measurement in power circuit

Acquisition of low speed balanced differential signals found in serial communications buses

Transients in switching power supplies, inverters and motor drives, electronic ballasts and CRT displays

Signals in the milliV range from sensors and other instrumentation

Certifications


IEC-1010.2-031 CAT I certified

Pollution Degree 2 certified

Note

The spring hooks supplied with this probe are rated at 1000 V.

관련된 링크들