STMicroelectronics MCP9701T Series, Digital Output Temperature & Humidity Sensor, Surface Mount, SMBus, ±2.5 %, 6-Pin
- RS 제품 번호:
- 190-8476P
- 제조사 부품 번호:
- STTS751-1DP3F
- 제조업체:
- STMicroelectronics
본 이미지는 참조용이오니 재확인이 필요하시면 문의해주세요.
대량 구매 할인 기용 가능
Subtotal 750 units (supplied on a reel)*
₩767,040.00
일시적 품절
- 2026년 7월 29일 부터 배송
더 자세한 내용이 필요하신가요? 필요한 수량을 입력하고 '배송일 확인'을 클릭하면 더 많은 재고 및 배송 세부정보를 확인하실 수 있습니다.
수량 | 한팩당 |
|---|---|
| 750 - 1475 | ₩1,022.72 |
| 1500 + | ₩1,000.16 |
* 참고 가격: 실제 구매가격과 다를 수 있습니다
- RS 제품 번호:
- 190-8476P
- 제조사 부품 번호:
- STTS751-1DP3F
- 제조업체:
- STMicroelectronics
사양
참조 문서
제정법과 컴플라이언스
제품 세부 사항
제품 정보를 선택해 유사 제품을 찾기
모두 선택 | 제품 정보 | 값 |
|---|---|---|
| 브랜드 | STMicroelectronics | |
| Product Type | Temperature & Humidity Sensor | |
| Output Type | Digital | |
| Interface Type | SMBus | |
| Sub Type | Temperature Sensor | |
| Accuracy | ±2.5 % | |
| Mount Type | Surface | |
| Pin Count | 6 | |
| Maximum Operating Temperature | 125°C | |
| Minimum Operating Temperature | -40°C | |
| Minimum Supply Voltage | 2.25V | |
| Maximum Supply Voltage | 3.6V | |
| Package Type | UDFN | |
| Width | 2.05 mm | |
| Length | 2.05mm | |
| Height | 0.5mm | |
| Standards/Approvals | No | |
| Series | MCP9701T | |
| Automotive Standard | No | |
| 모두 선택 | ||
|---|---|---|
브랜드 STMicroelectronics | ||
Product Type Temperature & Humidity Sensor | ||
Output Type Digital | ||
Interface Type SMBus | ||
Sub Type Temperature Sensor | ||
Accuracy ±2.5 % | ||
Mount Type Surface | ||
Pin Count 6 | ||
Maximum Operating Temperature 125°C | ||
Minimum Operating Temperature -40°C | ||
Minimum Supply Voltage 2.25V | ||
Maximum Supply Voltage 3.6V | ||
Package Type UDFN | ||
Width 2.05 mm | ||
Length 2.05mm | ||
Height 0.5mm | ||
Standards/Approvals No | ||
Series MCP9701T | ||
Automotive Standard No | ||
The STTS751 is a digital temperature sensor which communicates over a 2-wire SMBus 2.0 compatible bus. The temperature is measured with a user-configurable resolution between 9 and 12 bits. At 9 bits, the smallest step size is 0.5 °C, and at 12 bits, it is 0.0625 °C. At the default resolution (10 bits, 0.25 °C/LSB), the conversion time is nominally 21 milliseconds.
The open-drain EVENT output is used to indicate an alarm condition in which the measured temperature has exceeded the user-programmed high limit or fallen below the low limit. When the EVENT pin is asserted, the host can respond using the SMBus Alert Response Address (ARA) protocol to which the STTS751 will respond by sending its slave address.
The STTS751 is a 6-pin device that supports user-configurable slave addresses. Via the pull-up resistor on the Addr/Therm pin, one of four different slave addresses can be specified. Two order numbers (STTS751-0 and STTS751-1) provide two different sets of slave addresses bringing the total available to eight. Thus, up to eight devices can share the same 2-wire SMBus without ambiguity, thereby allowing monitoring of multiple temperature zones in an application.
The two-wire interface can support transfer rates up to 400 kHz.