STMicroelectronics, Surface Mount Microphone Condenser
- RS 재고 번호:
- 233-3022P
- 제조 부품 번호:
- PM8805TR
- 제조업체:
- STMicroelectronics
대량 구매 할인 기용 가능
Subtotal 10 units (supplied on a continuous strip)*
₩114,304.00
재고있음
- 2,363 개 단위 배송 준비 완료
더 자세한 내용이 필요하신가요? 필요한 수량을 입력하고 '배송일 확인'을 클릭하면 더 많은 재고 및 배송 세부정보를 확인하실 수 있습니다.
단위당 | 한팩당 |
|---|---|
| 10 - 99 | ₩11,430.40 |
| 100 - 249 | ₩11,223.60 |
| 250 - 499 | ₩11,016.80 |
| 500 + | ₩10,828.80 |
* 참고 가격: 실제 구매가격과 다를 수 있습니다
- RS 재고 번호:
- 233-3022P
- 제조 부품 번호:
- PM8805TR
- 제조업체:
- STMicroelectronics
사양
기술적 참조
제정법과 컴플라이언스
제품 세부 사항
제품 정보를 선택해 유사 제품을 찾기
모두 선택 | 제품 정보 | 값 |
|---|---|---|
| 브랜드 | STMicroelectronics | |
| Standard Operating Voltage | 100V | |
| Mounting Type | Surface Mount | |
| 모두 선택 | ||
|---|---|---|
브랜드 STMicroelectronics | ||
Standard Operating Voltage 100V | ||
Mounting Type Surface Mount | ||
IEEE 802.3bt PoE-PD interface with embedded dual active bridge
The PM8805 is a system in package for Power over Ethernet (PoE) and powered devices (PD) applications. It embeds: two active bridges and their driving circuitry, a charge pump to drive high-side MOSFETs, the hot-swap MOSFET and the standard single-signature interface IEEE 802.3bt-compliant, including detection, classification, UVLO and inrush current limitation. The active bridges sustain up to 1 A current and the hot-swap MOSFET is designed to safely work up to 2 A. The device performs IEEE 802.3bt physical layer classification scheme, providing the system with an indication of successful PSE-type. The device identifies a 4-pair PSE, monitoring the pairs of the Ethernet cable and providing the system with a dedicated matrix of Tx signals. The device works with power either from the Ethernet cable or from an external power source such as a wall adapter, with the likelihood of the auxiliary source being prevalent over PoE. The device is suitable to build the interface section of PoE switch mode power supplies targeting the highest conversion efficiency. It provides a PGD signal that can be used to enable a PWM controller, a DC-DC converter or a LED driver.
Key features
•System in package:
Dual-active-bridge with 100 V MOSFETs and 0.2 Ω total path resistance
100 V, 0.1 Ω hot-swap MOSFETs
PoE-PD single-signature interface, IEEE 802.3af/at/bt (draft 2.3)-compliant
•Detection and support of high power, 4-pair applications
•Support 12 V auxiliary sources
•Identifies which kind of PSE (standard or legacy) is connected and provides successful IEEE802.3 af/at/bt classification indications as combination of T0, T1 and T2 signals (open-drain)
•Smart operational mode selection by command signals: STBY, RAUX and FAUX
Dual-active-bridge with 100 V MOSFETs and 0.2 Ω total path resistance
100 V, 0.1 Ω hot-swap MOSFETs
PoE-PD single-signature interface, IEEE 802.3af/at/bt (draft 2.3)-compliant
•Detection and support of high power, 4-pair applications
•Support 12 V auxiliary sources
•Identifies which kind of PSE (standard or legacy) is connected and provides successful IEEE802.3 af/at/bt classification indications as combination of T0, T1 and T2 signals (open-drain)
•Smart operational mode selection by command signals: STBY, RAUX and FAUX
•Programmable classification current with 3.3 ms delay
•Autoclass feature (optional)
•Advanced energy-saving MPS timings
•Hot-swap current protection in two steps: DC with 1 ms delay and short-circuit with 10 μs delay
•Start-up phase (pre-charge of the output capacitor) due to an internally limited current source
•PGD signal (open-drain) to enable an external PWM controller
•Thermal shutdown protection
•VFQFPN package with 6 exposed pads
•Autoclass feature (optional)
•Advanced energy-saving MPS timings
•Hot-swap current protection in two steps: DC with 1 ms delay and short-circuit with 10 μs delay
•Start-up phase (pre-charge of the output capacitor) due to an internally limited current source
•PGD signal (open-drain) to enable an external PWM controller
•Thermal shutdown protection
•VFQFPN package with 6 exposed pads