최근 검색 기록

    SKF TMMD 100 Hand Bearing Puller, 10 → 100 mm capacity, 22 pieces

    RS 제품 번호:
    612-5694
    제조사 부품 번호:
    TMMD 100
    제조업체:
    SKF
    SKF
    모든 Bearing Pullers 열람하기
    3 <재고있음> 5-9영업일내 홍콩 발송
    12 <재고있음> 5-9영업일내 홍콩 발송
    Add to Basket
    수량

    추가완료!

    단가 Each

    ₩1,731,105.10

    수량한팩당
    1 +₩1,731,105.10
    RS 제품 번호:
    612-5694
    제조사 부품 번호:
    TMMD 100
    제조업체:
    SKF

    해당 안됨

    COO (Country of Origin):
    SI

    제정법과 컴플라이언스

    해당 안됨

    COO (Country of Origin):
    SI

    제품 세부 사항

    Blind Housing Bearing Puller Kit


    The SKF TMMD 100 is especially designed to allow easy and quick dismounting of deep groove ball bearings with interference fit on both rings. The puller is suitable for use in both blind housings and shaft applications. In addition to dismounting open bearings, the TMMD 100 can be used to dismount sealed bearings after the removal of the seal. The puller kit contains six sets of different size puller arms, two spindles and one handle packed in a carrying case. The TMMD 100 is suitable for dismounting up to 71 different SKF deep groove ball bearings from shaft diameter ranging between 10 mm and 100 mm.


    Features and Benefits


    • Claws designed to facilitate a precise fit in the bearings raceways
    • Each puller arm fitted with a spring for easy installation
    • Puller arms made from hardened steel for strength and longevity
    • Arm sizes 4, 5 and 6 are fitted with filling plates to accommodate a wide range of bearings
    • Hexagon headed spindle equipped with an anti-slip pin preventing the spanner from sliding down the spindle during dismounting
    • Limited rotation of the angle claw to allow easy insertion
    • Laser engraved designation on the arms for easy identification


    SKF Hand Bearing Puller, 22 Pieces - TMMD100


    This bearing puller kit from SKF makes it quick and easy to remove deep-groove ball bearings from shafts with diameters ranging from 10 mm to 100 mm. The puller claws are designed for a precise fit in the bearing's raceway, providing a tight grip and enabling high dismounting force with hand operation. Each puller arm is fitted with a spring for easy installation and a rubber cap keeps the arms attached to the spindle. The hexagonal spindle head also features an anti-slip pin, which stops the spanner from sliding down during use.


    • 22 pieces
    • 6 sets of puller arms
    • Can remove up to 71 different SKF deep-grove ball bearings
    • Shaft diameter capacity range of 10 mm to 100 mm


    Application Information


    • Machinery maintenance
    • Engineering workshops


    What's included in the kit?


    This bearing puller kit includes six sets of different size puller arms with three arms in each set. It also includes two spindles, one handle and a padded carrying case to make transporting the kit easy.


    What are the puller arms made from?


    They're made from hardened steel for strength and longevity, and they're laser engraved for easy identification.



    사양

    속성
    Capacity10 → 100 mm
    Puller TypeBearing Puller
    OperationHand
    Number of Pieces22
    3 <재고있음> 5-9영업일내 홍콩 발송
    12 <재고있음> 5-9영업일내 홍콩 발송
    Add to Basket
    수량

    추가완료!

    단가 Each

    ₩1,731,105.10

    수량한팩당
    1 +₩1,731,105.10