Vero Technologies 10-2449 1 Stripboard Epoxy 160 mm FR4 100 mm

모든 Stripboards 열람하기
대량 구매 할인 기용 가능

Subtotal (1 unit)*

₩57,960.40

Add to Basket
수량 선택 또는 입력
재고있음
  • 9 개 단위 배송 준비 완료
  • 추가로 2026년 5월 08일 부터 16 개 단위 배송
더 자세한 내용이 필요하신가요? 필요한 수량을 입력하고 '배송일 확인'을 클릭하면 더 많은 재고 및 배송 세부정보를 확인하실 수 있습니다.
수량
한팩당
1 - 9₩57,960.40
10 - 39₩57,152.00
40 +₩56,531.60

* 참고 가격: 실제 구매가격과 다를 수 있습니다

RS 제품 번호:
434-627
제조사 부품 번호:
10-2449
제조업체:
Vero Technologies
제품 정보를 선택해 유사 제품을 찾기
모두 선택

브랜드

Vero Technologies

Board Material

Epoxy

Product Type

Stripboard

Number of Sides

1

Hole Diameter

1.02mm

Hole Layout

Hole Grid 2.54 x 2.54 mm

Hole Pitch

2.54mm

FR Material Grade

FR4

Board Thickness

1.6mm

Length

160mm

Width

100 mm

Standards/Approvals

DIN 41612, DIN 41494

COO (Country of Origin):
GB

KM6 Veroboard® boards for DIN 41612 connectors


Single-sided boards combining the advantages of Veroboard, the flexibility of Eurocards and DIN 41612 connectors.

For wiring by wrapping applications, spacing of 3.81 on the double height boards keeps the board route aligned on the grid of the adjacent connectors.

Silk-screened component installation grid.

The cutter (stock number 543-535) allows rapid completion of a circuit by interrupting the copper tracks on request.

DIN Type Stripboards


Suitable for use with the KM6-II eurocard sub-rack systems


The double-sided microboards are designed for microprocessor applications where compatibility, flexibility, high density and screening are of prime importance. VCC rails and a VCC bus are provided but not connected, so that individual rails may be committed as required. 64//96-way DIN 41612 indirect edge connectors may be fitted at either end.

The 3U (100x160) and 6U (233.4x160) boards are available with plated through holes (pth) as an alternative to the standard types. These boards have the added advantage of linking the top with the bottom pads directly via the holes, thereby dispensing with the need to fit linking pins, etc. Also the integrity of the joint is improved as the solder forms round the component lead on both surfaces, in addition to flowing through the hole. This helps to produce a solid and reliable connection, which is very important in applications where a high degree of vibration may be encountered.

Eurocards are manufactured from either epoxy glass material (blue) to BS4584 Part 3 or 16, or SRBP (synthetic resin bonded paper) material to BS4584 Part 5. Card thickness is 1.6mm. Copper 305g/m2 (1oz/ft2). Holes 1.0mm (0.040in.) dia. are pre-drilled on a 2.54mm matrix and all cards can be used with indirect edge connectors to DIN41612 (see Connectors/Terminals) except SRBP stripboard.

Note

Single-sided microboards have the same wiring pattern as the double-sided types, but omit the ground plane and 0 Volt rails on the component side of the card.

관련된 링크들