SKF Nitrile Rubber (NBR) Seal, 25 mm ID, 40 mm OD, 10 mm
- RS 제품 번호:
- 266-9040
- 제조사 부품 번호:
- 25X40X10 HMSA10 RG
- 제조업체:
- SKF
Subtotal (1 pack of 10 units)*
₩19,520.00
재고있음
- 추가로 2026년 7월 13일 부터 20 개 단위 배송
더 자세한 내용이 필요하신가요? 필요한 수량을 입력하고 '배송일 확인'을 클릭하면 더 많은 재고 및 배송 세부정보를 확인하실 수 있습니다.
수량 | 한팩당 | 한팩당* |
|---|---|---|
| 10 + | ₩1,952.00 | ₩19,520.00 |
* 참고 가격: 실제 구매가격과 다를 수 있습니다
- RS 제품 번호:
- 266-9040
- 제조사 부품 번호:
- 25X40X10 HMSA10 RG
- 제조업체:
- SKF
사양
참조 문서
제정법과 컴플라이언스
제품 세부 사항
제품 정보를 선택해 유사 제품을 찾기
모두 선택 | 제품 정보 | 값 |
|---|---|---|
| 브랜드 | SKF | |
| Inside Diameter | 25mm | |
| Product Type | Seal | |
| Outside Diameter | 40mm | |
| Seal Type | Rotary Shaft Seal | |
| Thickness | 10mm | |
| Seal Material | Nitrile Rubber (NBR) | |
| 모두 선택 | ||
|---|---|---|
브랜드 SKF | ||
Inside Diameter 25mm | ||
Product Type Seal | ||
Outside Diameter 40mm | ||
Seal Type Rotary Shaft Seal | ||
Thickness 10mm | ||
Seal Material Nitrile Rubber (NBR) | ||
- COO (Country of Origin):
- CN
SKF Seal, 25mm Inside Diameter, 40mm Outside Diameter - 25X40X10 HMSA10 RG
This seal is a rotary shaft seal designed to separate rotating and stationary components and retain lubricants in rotating assemblies. It features a rubber outer circumference and an elastomeric primary sealing element to maintain oil or grease containment while limiting ingress of contaminants in industrial rotating equipment.
Features & Benefits
• Nitrile construction resists common oils and greases
• Garter spring maintains consistent lip contact under rotation
• Auxiliary non-contact lip improves contamination exclusion
• Accommodates minor misalignment during shaft operation
• Garter spring maintains consistent lip contact under rotation
• Auxiliary non-contact lip improves contamination exclusion
• Accommodates minor misalignment during shaft operation
**Applications**
• Suitable for industrial motor and gearbox shafts
• Ideal for automation actuator rotary joints
• Used with electrical motor drive assemblies
• Can be used for centrifugal pump shaft Seals
• Ideal for automation actuator rotary joints
• Used with electrical motor drive assemblies
• Can be used for centrifugal pump shaft Seals
What temperature range can it withstand in continuous service?
It operates from −40°C up to 100°C in normal use with short-term tolerance to 120°C.
How does it behave at higher shaft speeds?
It is rated for circumferential speeds up to 5.03 m/s and rotational speeds up to 3840 rev/min.
Is it compatible with pressurised housings?
It is intended for low differential pressure conditions and is specified for a 0.03 N/mm pressure differential.
What housing and shaft interfaces are required for correct fit?
The seal fits into a 40mm bore and runs on a 25mm shaft with a 10mm section width.
Are there related accessories to aid installation on worn shafts?
A speedi-sleeve accessory is referenced for use when shaft repair or undersize restoration is needed.
관련된 링크들
- SKF Nitrile Rubber (NBR) Seal, 25 mm ID, 40 mm OD, 8 mm
- SKF Nitrile Rubber (NBR) Seal, 25 mm ID, 40 mm OD, 7 mm
- SKF Nitrile Rubber (NBR) Seal, 25 mm ID, 40 mm OD, 5 mm
- SKF Nitrile Rubber (NBR) Seal, 40 mm ID, 72 mm OD, 10 mm
- SKF Nitrile Rubber (NBR) Seal, 40 mm ID, 80 mm OD, 10 mm
- SKF Nitrile Rubber (NBR) Seal, 40 mm ID, 62 mm OD, 10 mm
- SKF Nitrile Rubber (NBR) Seal, 17 mm ID, 40 mm OD, 10 mm
- SKF Nitrile Rubber (NBR) Seal, 40 mm ID, 68 mm OD, 10 mm