Tektronix ADA400A Differential Preamplifier Oscilloscope Module for Use with TDS400 Series, TDS5000 Series, TDS600

모든 Oscilloscope Modules 열람하기

Subtotal (1 unit)*

₩7,388,813.60

Add to Basket
수량 선택 또는 입력
재고있음
  • 1 개 단위 배송 준비 완료
더 자세한 내용이 필요하신가요? 필요한 수량을 입력하고 '배송일 확인'을 클릭하면 더 많은 재고 및 배송 세부정보를 확인하실 수 있습니다.
수량
한팩당
1 +₩7,388,813.60

* 참고 가격: 실제 구매가격과 다를 수 있습니다

RS 제품 번호:
349-8214
제조사 부품 번호:
ADA400A
제조업체:
Tektronix
제품 정보를 선택해 유사 제품을 찾기
모두 선택

브랜드

Tektronix

Module Type

Differential Preamplifier

Product Type

Oscilloscope Module

For Use With

TDS400 Series, TDS5000 Series, TDS600 Series, TDS500 Series, TDS7000 Series, TDS700 Series

Model Number

ADA400A

Standards/Approvals

CE, ISO 14001, ISO 9001

제외

COO (Country of Origin):
US

Tektronix ADA400A 1 MHz Differential Preamplifier


10μV/div Sensitivity

Low Pass filters for 100Hz, 3kHz, 100Hz and Full (1 MHz)

Typically 100 dB CMRR DC to 10 kHz

Selectable Gain: 100, 10, 1 or 0.1

Accurately measures signal as small as 5uV

Integral Probe Power with TEKPROBE ™ BNC

The ADA400A Active Differential Preamplifier allows direct oscilloscope measurements of very low amplitude voltages and signals which are not ground referenced. The high impedance of both inputs eliminates the need to add additional ground points in the DUT, thereby avoiding circulating currents which disturb the measurement or the circuit.

The high gain and extremely high common mode rejection provide usable measurements of voltages as low as 5μV, even in high noise environments. Selectable bandwidth limiting reduces normal mode noise from digital logic, switch mode power supplies and line frequency sources. Adjustable differential offset allows the user to null out transducer bridge bias and galvanic potential from the test set-up. An "infinite impedance" mode can be selected in the two highest gain ranges allowing accurate measurements of signals with high source impedance. It is specifically designed to operate on Tektronix oscilloscopes with TEKPROBE® interface.

Tektronix ADA400A 1 MHz Differential Preamplifier


The ADA400A Active Differential Preamplifier allows direct oscilloscope measurements of very low amplitude voltages and signals which are not ground referenced. The high impedance of both inputs eliminates the need to add additional ground points in the DUT, thereby avoiding circulating currents which disturb the measurement or the circuit.,The high gain and extremely high common mode rejection provide usable measurements of voltages as low as 5μV, even in high noise environments. Selectable bandwidth limiting reduces normal mode noise from digital logic, switch mode power supplies and line frequency sources. Adjustable differential offset allows the user to null out transducer bridge bias and galvanic potential from the test set-up. An "infinite impedance" mode can be selected in the two highest gain ranges allowing accurate measurements of signals with high source impedance. It is specifically designed to operate on Tektronix oscilloscopes with TEKPROBE® interface

10μV/div Sensitivity

Low-pass filter: 100Hz, 3kHz, 100Hz or Full (1 MHz)

Typically 100 dB CMRR DC to 10 kHz

Selectable Gain: 100, 10, 1 or 0.1

Accurately measures signal as small as 5uV

Integral Probe Power with TEKPROBE™BNC

관련된 링크들