Push Fit Fittings

Push fit fittings are very common in the market today because they are easy to install with simple push in connections and are ready to use immediately. They work by pushing the pipe into the fitting and the metal spurs inside the fittings tightly grip the pipes. The O rings inside the fittings creates a safe, secure and watertight seal. When fitted correctly the joint will last a long time.
These push fit fittings can be used on both copper and plastic pipes. When using a plastic pipe it requires a small metal sleeve/insert to be pushed into the pipe which prevents the pipe from collapsing. When using copper pipe the insert is not needed.
Suitable for plumbing of hot and cold water services and central heating systems. Also plastic push fit fittings are less expensive than copper fittings.
Push fit fittings types can include:
• Elbow tap connector
• Straight coupler
• Socket Reducer
• Collet cover which prevents tampering or accidental removal
Advantages of Push fit fittings:
• Fast connection – easier than other plumbing fittings, reduces installation time
• No specialist plumbing tools needed – for example you do not have to solder or glue the fittings
• Pipes do not need to be completely dry
• Easily disconnected
How are the fittings assembled?
· Main valve body
· Rubber sealing washer for a watertight seal
· Washer jumper that holds the rubber washer in place
· Pipe clamp that holds the pipe in place – has metal teeth that grip the pipe one way so you can push it on the pipe but not pull it off.
· End nut that holds all of this together in one piece
Rubber washer goes in first, then washer jumper, pipe clamp and finally the end nut.
Hints and tips:
· Do not put your finger in the clamp as there are steel grit rings on the inside which will harm you
· Do not cut the pipe with a hacksaw and make sure the pipe isn’t damaged
· It is advised not to mix up the fittings, only use the correct fittings for that pipe. You can use copper pipe with push fit fittings make sure there are no burrs after cutting as this could cause leakage and problems later on.
· Some manufacturers use silicon grease on the inside of the fittings
· Need to be in open position before inserting the pipe

...
Read more Read less

검색 필터링

총 6개 제품 중 1번째-6번째 제품을 조회 중
한장내 검색 결과 수
제품설명 단가 Material Fitting Direction Fitting Type Compatible Pipe Size 1 Compatible Pipe Size 2 Thread Size
RS 제품 번호 784-5059
제조사 부품 번호PB715
제조사Polyplumb
₩7,884.192
Each
수량
Brass Straight Tap Connector 15mm - 1/2in
RS 제품 번호 784-5162
제조사 부품 번호PB722
제조사Polyplumb
₩9,708.634
Each
수량
Brass Straight Tap Connector 22mm - 3/4in
RS 제품 번호 784-5061
제조사 부품 번호PB1715RS
제조사Polyplumb
₩10,894.520
Each
수량
Brass 90° Tap Connector 15mm - 1/2in
RS 제품 번호 340-6849
제조사 부품 번호PM1915E
제조사JG Speedfit
₩409.775
Each (In a Pack of 20)
수량
- - Collet Cover 15mm - -
RS 제품 번호 784-5052
제조사 부품 번호PB015-10
제조사Polyplumb
₩27,620.013
1 Bag of 10
Bag(s)
- Straight Coupler 15mm - -
RS 제품 번호 784-5074
제조사 부품 번호PB1815RS
제조사Polyplumb
₩4,720.380
Each
수량
- Straight Reducer 15mm 10mm -